home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Software Vault: The Diamond Collection
/
The Diamond Collection (Software Vault)(Digital Impact).ISO
/
cdr40
/
x1j4pk96.zip
/
QUICKREF.TXT
< prev
next >
Wrap
Text File
|
1995-02-08
|
12KB
|
265 lines
THENET X1-J4 QUICK REFERENCE GUIDE
==================================================================
SWITCH COMMANDS
ACL [{CALLSIGN + VALUE} | {CALLSIGN - VALUE} |
{ * VALUE } | { & value }]
ADC
ADC1 [ * | Units_for_Voltmeter_channel_1 ] (see note 6)
ADC2 [ * | Units_for_voltmeter_channel_2 ] (see note 6)
ADC3 [ * | Units_for_Voltmeter_channel_3 ] (see note 6)
ADC4 [ * | Units_for_voltmeter_channel_4 ] (see note 6)
ALIAS [ * | NEW_ALIAS ]
ARP [ipaddr [{ - ptcl } | [+ [P] ptcl callsign [DG | VC ]]]
ARPTIMER [ * | enable_flag [ * | timer_rate ] ]
AUDIT [ NUMBER_FROM_0_TO_255 ]
BBS [ CALLSIGN | * | ? ]
BBSALIAS [ * | NEW_ALIAS ]
BRATE [ * | radio_brate [ * | rs232_baud_rate ]] (PK96 only )
BTEXT [ * | BEACON_MESSAGE_TEXT ] (see note 6)
BYE
CALIBRATE [PERIOD_VALUE_FROM_1_TO_60 [TOGGLE_VALUE_1_TO_PERIOD ] ]
CLOSEDOWN A
CONNECT [ CALLSIGN [ [V] DIGILIST ... ]
CQ [ MESSAGE_FOR_CQ_PACKET ]
CTEXT [ * | CONNECT_MESSAGE_TEXT ] (see note 6)
DXCLUSTER [ CALLSIGN | * | ? ]
DXCALIAS [ * | NEW_ALIAS ]
HELP
HOST [ CALLSIGN | * | ? ]
HOSTALIAS [ * | NEW_ALIAS ]
INFO [ SYSOP_SET_MESSAGE ] (see note 6)
IPADDRESS [ NEW_IP_ADDRESS ]
IPBROADCAST [ NEW_IP_ADDRESS ]
IPROUTE [ipaddr [/bits ] [ - | { + port [ipgateway[metric ]]]]
IPSTATS [ { NEWPARAM | * } { NEWPARAM | * } ..... ] (see note 5)
L3MHEARD [ NUMBER_FROM_1_TO_100 ]
LINKS
MANAGER
METER [ { new_value | * } ... ] (see note 5)
MHEARD [ NUMBER_FROM_1_TO_100 ]
MODE [ { NEWPARAM | * } { NEWPARAM | * } ..... ] (see note 5)
MTU [ list_of_parameters ] (see note 5)
NODES [* [*] | NODECALL {+|-} IDENT QUAL COUNT PORT NEIGHBOUR
[DIGIS]]
PARMS [ { NEWPARAM | * } { NEWPARAM | * } ..... ] (see note 5)
QUIT
RESET [ ANY_CHARACTER ]
ROUTES [ PORT NODECALL [ DIGILIST ... ] { + | - } PATHQUALITY ]
STATS
SYSOP
TALK [ STRING ]
UI DEST STRING_OF_TEXT_TO_BE_SENT_IN_UI_FRAME
USERS
------------------------------------------------------------------
Note 1 Any command may be enabled or disabled by the
use of the '+' or '-' modifier, as shown below :
ANY_COMMAND [ + | - | THAT_COMMANDS_PARAMETERS ]
Commands may be caused to be displayed or not in
the prompt screen if the '-' or '+' is followed
by 'D' ( or 'd' )
Note 2 IP addresses are of the form nnn.nnn.nnn.nnn
where nnn is a number 0..255
Note 3 IProute port parameter is 0 for radio or 1 for
rs232
Note 4 ARP ptcl parameter is AX.25 or Net/Rom (may be
abbreviated)
Note 5 The commands will accept the 'old' syntax of '*
* * value...' or the new offset & value syntax of
'/ parameter_number value'
Note 6 Voltmeter channels 1,2,3,4 correspond to ADC channels 3,4,1,2
respectively. The ADC command reads them.
HOST 'ESCAPE' COMMANDS
<escape> C
<escape> D
<escape> P [ NEW_PASSWORD ]
==================================================================
UNDERSTANDING ACL VALUES UNDERSTANDING AUDIT BITS
------------------------------------------------------------------
Bit Function | Bit Function
=================================|================================
0 Bar all incoming L2 connects | 0 Issue L1 stats every 10 mins
1 Bar outgoing L2 downlinks | 1 Audit L2 connects & discs
2 Ignore nodes broadcasts | 2 unused
3 Bar gatewaying at level 3 | 3 Audit L4 connects & discs
4 Bar incoming L4 connects | 4 Audit L7 use of sysop cmd
5 Bar outgoing L4 connects | 5 Audit all L7 switch commands
6 ignore SSID in searching | 6 Issue CPU stats every 10mins
7 unused | 7 unused
==================================================================
PARMS PARAMETERS
Number Min Max Function
-----------------------------------------------------------
1 1 400 Maximum number of destination nodes
2 0 255 Minimum quality for auto update
3 0 255 HDLC ( radio, port 0 ) default quality
4 0 255 RS232 ( crosslink, port 1 ) default quality
5 0 255 Initial value for obsolescence counter
6 1 255 Minimum obsolescence for node broadcast
7 0 65535 Auto update broadcast interval (seconds)
8 0 255 Level 3 ( network ) Time To Live Initialiser
9 5 600 Level 4 ( transport ) timeout (seconds)
10 1 127 Level 4 ( transport ) retries
11 1 60 Level 4 ( transport ) ack delay (seconds)
12 1 1000 Level 4 ( transport ) busy delay (seconds)
13 1 127 Level 4 ( transport ) window size (frames)
14 1 127 Level 4 ( transport ) congestion ctrl threshold
15 0 65535 Level 7 ( switch ) inactivity timeout (seconds)
16 0 255 Persistance for transmit delay
17 0 127 Persistance slottime delay (10's of msecs)
18 1 15 Level 2 ( link ) T1 timeout, ie FRACK (seconds)
19 1 7 Level 2 ( link ) window size (packets)
20 0 127 Level 2 ( link ) retries
21 0 6000 Level 2 ( link ) T2 timeout (10's of msecs)
22 0 65535 Level 2 ( link ) T3 timeout (10's of msecs)
23 0 1 Level 2 ( link ) digipeat enable flag
24 0 1 Callsign validation flag
25 0 2 Node beacon ctrl (0=off, 1=if active, 2=always)
26 0 1 CQ broadcasts enable flag
==================================================================
MODE PARAMETERS
Number Min Max Function
-----------------------------------------------------------
1 0 1 Hardware handshake host control mode flag
2 0 3600 CWID repeat period ( seconds )
3 4 10 CWID speed ( 10's msecs per dot )
4 0 3 Nodes broadcast channel enable flags where
0=none, 1=HDLC only, 2=RS232 only, 3=Both ports
5 0 3 Crosslink protocol selection
0=crosslink, 1=KISS,
2=KISS+selective copy, 3=KISS+allcopy
6 0 255 TX keyup delay ( 10's of milliseconds )
7 0 1 Full duplex enable flag
8 0 65535 RS232 ( port 1 ) node broadcast period ( secs )
9 0 3 Node broadcast algorithm control flags
0=off, 2=RS232 port, 1 & 3 not normally used
10 600 3600 Beacon interval ( seconds )
11 0 2 Connect redirection to BBS flag
12 0 255 Help messages flags, 8 bit TALK, case & TEXNET
13 0 3 Hash node broadcast disable (one bit per port)
14 0 1 Enable extra aliases monitoring if set
15 0 1 Enable auto reconnect to node after remote dis
16 0 3 Slime trail control. Each bit controls...
Bit 0 if set hides slime trails in nodes list
Bit 1 if set causes slime trails to be ignored
17 0 3 Digipeat control. Each bit controls ...
Bit 0 set makes node to refuse digi'd L2 uplink
Bit 1 set, node refuses to allow digi downlinks
==================================================================
IPSTAT PARAMETERS
Number Min Max Function ( Those marked '*' are not used )
-----------------------------------------------------------
1 0 3 ip L2 AX.25 Modes ( 1 bit per port, 1=DG )
2 0 1 ip Forwarding, 1=enable router, 0=disable
3 2 255 ip Default TTL
4 0 0 ip In Receives
5 0 0 ip In Header Errors
6 * 0 0 ip In Address Errors
7 0 0 ip Forwarded Datagrams
8 0 0 ip In Unknown Protocols
9 * 0 0 ip In Discards ( TTL exceeded )
10 * 0 0 ip In Delivers
11 0 0 ip Output Requests
12 * 0 0 ip Output Discards
13 0 0 ip Output No Routes
14 * 1 30 ip Reasm Timeout
15 * 0 0 ip Reasm Requireds
16 * 0 0 ip Reasm OKs
17 * 0 0 ip Reasm Fails
18 0 0 ip Frag OKs
19 * 0 0 ip Frag Fails
20 0 0 ip Frag Creates
=================================================================
MTU PARAMETERS
Number Min Max Function
-----------------------------------------------------------
1 64 1024 IP Port 0 ( Radio Port ) Level 2 AX.25 MTU
2 64 1024 IP Port 1 ( RS232 Port ) Level 2 AX.25 MTU
3 64 236 IP Net/Rom port MTU
4 257 1025 Level 2 Max data bytes in a packet before error
5 328 1096 Level 2 Total max packet size in bytes
=================================================================
METER PARAMETERS
Number Min Max Function
-----------------------------------------------------------
1 0 511 The meter mode flags
2 0 255 The deviation meter scaling factor
3 0 255 The signal strength meter noise floor value
4 0 255 The S meter display format multiplier
5 0 255 The dBm meter display format multiplier
6 0 255 The dBm noise floor value
7 0 255 The voltmeter channel 1 multiplier
8 0 255 The voltmeter channel 2 multiplier
9 0 255 Voltmeter Channel 1 offset value
10 0 255 Voltmeter Channel 2 offset value
11 0 255 The voltmeter channel 3 multiplier
12 0 255 The voltmeter channel 4 multiplier
13 0 255 Voltmeter Channel 3 offset value
14 0 255 Voltmeter Channel 4 offset value
==================================================================
THE METER MODE FLAGS ( METER parameter 1 )
BIT If set, then ....
-----------------------------------------------------------
0 The deviation meter is enabled
1 The signal strength meter is enabled
2 The signal strength is shown as S points rather than dBm
3 ADC channel 3 is enabled ( voltmeter channel 1 )
4 ADC channel 4 is enabled ( voltmeter channel 2 )
5 Voltmeter channel 1 divisor is 1000 rather than 100
6 Voltmeter channel 2 divisor is 1000 rather than 100
7 Voltmeter channel 1 display resolution is 0.1 not 1.0
8 Voltmeter channel 2 display resolution is 0.1 not 1.0
9 ADC channel 1 is enabled ( voltmeter channel 3 )
10 ADC channel 2 is enabled ( voltmeter channel 4 )
11 Voltmeter channel 3 divisor is 1000 rather than 100
12 Voltmeter channel 4 divisor is 1000 rather than 100
13 Voltmeter channel 3 display resolution is 0.1 not 1.0
14 Voltmeter channel 4 display resolution is 0.1 not 1.0
==================================================================
HELP MESSAGES FLAGS ( MODE Parameter 12 )
BIT FUNCTION
-----------------------------------------------------------
0 If set, the 'please wait, trying xxxx' operates
1 If set, all commands appear in help for sysop
2 If set, the 'goodbye' message is given
3 If set, a welcome message is enabled ( CTEXT )
4 If set, nodes are shown as 'alias:callsign'
5 If set, TALK data is passed as 8 bit data
6 If set, node aliases are deemed to be case sensitive
7 If set, enables the TexNet "*** LINKED to" interface
=================================================================
ARPTIMER PARAMETERS
Number Min Max Function
-----------------------------------------------------------
1 0 1 0 disables ARP table mgmt, 1 enables
2 15 1440 ARP entry expiry time in minutes